Standard conditions for temperature and pressure

You don't need to be Editor-In-Chief to add or edit content to WikiDoc. You can begin to add to or edit text on this WikiDoc page by clicking on the edit button at the top of this page. Next enter or edit the information that you would like to appear here. Once you are done editing, scroll down and click the Save page button at the bottom of the page.

Please Take Over This Page and Apply to be Editor-In-Chief for this topic: There can be one or more than one Editor-In-Chief. You may also apply to be an Associate Editor-In-Chief of one of the subtopics below. Please mail us [1] to indicate your interest in serving either as an Editor-In-Chief of the entire topic or as an Associate Editor-In-Chief for a subtopic. Please be sure to attach your CV and or biographical sketch.

In chemistry and other sciences, STP or standard temperature and pressure is a standard set of conditions for experimental measurements, to enable comparisons to be made between sets of data. Internationally, the current STP defined by the IUPAC (International Union of Pure and Applied Chemistry) is an absolute pressure of 100 kPa (1 bar) and a temperature of 273.15 K (0 °C).^[1] Other organizations have established a variety of alternative definitions for the standard reference conditions of temperature and pressure.

In industry and commerce, it is necessary to define the standard reference conditions of temperature and pressure when expressing a gas volume or a volumetric flow rate because the volume of a gas varies with the temperature and pressure of the gas. The available data on the various definitions of standard reference conditions clearly indicates that there is no universally accepted definition of the standard conditions of temperature and pressure. For that reason, simply stating that a gas flow rate is 10,000 m³/h (i.e. cubic meters per hour) at "standard conditions" or at "STP" has no meaning unless the reference conditions that were applied are clearly stated.

Definitions used in the past

For a great many years, most engineers, chemists, physicists and other scientists using the metric system of units defined the standard reference conditions of temperature and pressure for expressing gas volumes as being 0 °C (273.15 K) and 101.325 kPa (i.e., 1 atmosphere of absolute pressure). During those same years, the most commonly used standard reference conditions for people using the Imperial or customary USA system of units was 60 °F (520 °R) and 14.696 psia (i.e., 1 atmosphere of absolute pressure) because it was almost universally used by the oil and gas industries worldwide.

The above two definitions are no longer the most commonly used definitions in either the metric, Imperial or the customary USA system of units. Some of the many different definitions currently in use are presented in the next section.

It was also common in the past, when using the metric system of units, to refer to a Normal Cubic Meter (Nm³) and to define it as being at 0 °C (273.15 K) and 101.325 kPa (i.e. 1 atmosphere of absolute pressure). As shown in the following section, that notation is no longer appropriate unless the specific reference conditions are explicitly stated, since there are currently many different metric system definitions of what constitutes standard reference conditions.

In the same manner, it is also no longer appropriate to refer to a standard cubic foot (scf) unless the specific reference conditions are explicitly stated, again because there are currently many different definitions of the standard reference condition in both the Imperial and the customary U.S. systems of units. In particular, OPEC and a majority of the natural gas industry in North America have adopted 60 °F and 14.73 psia as their standard reference conditions for expressing natural gas volumes and flow rates (rather than the 60 °F and 14.696 psia commonly used previously).

Definitions in current use

There are a great many different definitions of the standard reference conditions currently being used. Table 1 presents twelve such variations of standard condition definitions - and there are quite a few others as well.

As shown in the table, the IUPAC (International Union of Pure and Applied Chemistry) currently defines standard reference conditions as being 0 °C and 1 bar (i.e., 100 kPa) of absolute pressure rather than the 1 atmosphere (i.e. 101.325 kPa) of absolute pressure used in the past. In fact, the IUPAC's current definition has been in existence since 1982.^[1]

As further shown in the table, the oil and gas industries have to a large extent changed from their past usage of 60 °F and 14.696 psia to their current usage of 60 °F and 14.73 psia. This is especially true of the natural gas industry in North America.

For the SATP used in presenting chemical thermodynamic properties (such as those published by the National Bureau of Standards as included in Table 1) that the pressure is standardized at 1 bar (100 kPa) but the temperature may vary and needs to be specified separately.

It should also be noted that the International Organization for Standardization (ISO), the United States Environmental Protection Agency (EPA) and National Institute of Standards and Technology (NIST) each have more than one definition of standard reference conditions in their various standards and regulations.

The table makes it quite obvious that it is absolutely necessary to clearly state the temperature and pressure reference conditions whenever expressing a gas volume or gas volumetric flowrate. It is equally important to state whether the gas volume is expressed on a dry basis or a wet basis. As noted in the table, some of the current definitions of the reference conditions include a specification of the percent relative humidity (% RH).

Table 1: Standard reference conditions in current use

Temperature	Absolute pressure	Relative humidity	Publishing or establishing entity
°C	kPa	% RH
0	100.000		IUPAC (present definition)[1]
0	101.325		IUPAC (former definition),[1] NIST,[1] ISO 10780[1]
15	101.325	0 [4], [5]	ISA,[1] ISO 13443,[1] EEA,[1] EGIA[1]
20	101.325		EPA,[1] NIST[1]
25	101.325		EPA[1]
25	100.000		SATP[1]
20	100.000	0	CAGI[1]
15	100.000		SPE[1]
°F	psia	% RH
60	14.696		SPE,[1] OSHA,[1] SCAQMD[1]
60	14.73		EGIA,[1] OPEC,[1] EIA[1]
59	14.503	78	Army Standard Metro[1]
59	14.696	60	ISO 2314, ISO 3977-2[1]
°F	in Hg	% RH
70	29.92	0	AMCA,[1] air density = 0.075 lbm/ft³

Notes:

• 101.325 kPa = 1 atmosphere = 1.01325 bar ≈ 14.696 psi
• 100.000 kPa = 1 bar ≈ 14.504 psi
• 14.503 psi ≈ 750 mmHg ≈ 100.0 kPa ≈ 1 bar
• 14.696 psi ≈ 1 atm = 101.325 kPa
• 14.73 psi ≈ 30 inHg ≈ 1.0156 bar ≈ 101.560 kPa
• All pressures are absolute pressures (not gauge pressures)
• 59 °F = 15 °C
• 60 °F ≈ 15.6 °C
• dry = 0 percent relative humidity = 0 % RH

The full names of the entities listed in Table 1:

• IUPAC: International Union of Pure and Applied Chemistry
• NIST: National Institute of Standards and Technology
• ISA: ICAO's International Standard Atmosphere
• ISO: International Organization for Standardization
• EEA: European Environment Agency
• EGIA: Electricity and Gas Inspection Act (of Canada)
• EPA: United States Environmental Protection Agency
• SATP: Standard Ambient Pressure and Temperature
• CAGI: Compressed Air and Gas Institute
• SPE: Society of Petroleum Engineers
• OSHA: U.S. Occupational Safety and Health Administration
• SCAQMD: California's South Coast Air Quality Management District
• OPEC: Organization of Petroleum Exporting Countries
• EIA: U.S. Energy Information Administration
• Std. Metro: U.S. Army's Standard Metro (used in ballistics)
• AMCA: Air Movement and Control Association This AMCA standard applies only to air.

International Standard Atmosphere

In aeronautics and fluid dynamics the term "International Standard Atmosphere" is often used to denote the variation of the principal thermodynamic variables (pressure, temperature, density, etc.) of the atmosphere with altitude at mid latitudes.

Standard laboratory conditions

Due to the fact that many definitions of standard temperature and pressure differ in temperature significantly from standard laboratory temperatures (e.g., 0°C vs. ~25°C), reference is often made to "standard laboratory conditions" (a term deliberately chosen to be different from the term "standard conditions for temperature and pressure", despite its semantic near identity when interpreted literally). However, what is a "standard" laboratory temperature and pressure is inevitably culture-bound, given that different parts of the world differ in climate, altitude and the degree of use of heat/cooling in the workplace. This concept of "standard laboratory conditions" is taught as part of the New South Wales high school chemistry syllabus.^[1]

Molar volume of a gas

It is equally as important to indicate the applicable reference conditions of temperature and pressure when stating the molar volume of a gas^[1] as it is when expressing a gas volume or volumetric flow rate. Stating the molar volume of a gas without indicating the reference conditions of temperature and pressure has no meaning and it can cause confusion.

The molar gas volumes can be calculated with an accuracy that is usually sufficient by using the universal gas law for ideal gases. The usual expression is:

…which can be rearranged thus:

where (in SI metric units):

P	= the gas absolute pressure, in Pa
n	= number of moles, in mol
V / n	= the gas molar volume, in m³/mol
T	= the gas absolute temperature, in K
R	= the universal gas law constant of 8.3145 m³·Pa/(mol·K)

or where (in customary USA units):

P	= the gas absolute pressure, in psia
n	= number of moles, in lbmol
V / n	= the gas molar volume, in ft³/lbmol
T	= the gas absolute temperature, in °R
R	= the universal gas law constant of 10.7316 ft³·psia/(lbmol·°R)

The molar volume of any ideal gas may be calculated at various standard reference conditions as shown below:

• V / n = 8.3145 × 273.15 / 101.325 = 22.414 m³/kmol at 0 °C and 101.325 kPa absolute pressure
• V / n = 8.3145 × 273.15 / 100.000 = 22.711 m³/kmol at 0 °C and 100 kPa absolute pressure
• V / n = 10.7316 × 519.67 / 14.696 = 379.48 ft³/lbmol at 60 °F and 14.696 psia absolute pressure
• V / n = 10.7316 × 519.67 / 14.730 = 378.61 ft³/lbmol at 60 °F and 14.73 psia absolute pressure

The technical literature can be confusing because many authors fail to explain whether they are using the universal gas law constant R, which applies to any ideal gas, or whether they are using the gas law constant R_s, which only applies to a specific individual gas. The relationship between the two constants is R_s = R / M, where M is the molecular weight of the gas.

The US Standard Atmosphere uses 8.31432 m³·Pa/(mol·K) as the value of R for all calculations. (See Gas constant)

References

External links

• "Standard conditions for gases" from the IUPAC Gold Book.
• "Standard pressure" from the IUPAC Gold Book.
• "STP" from the IUPAC Gold Book.
• "Standard state" from the IUPAC Gold Book.

ar:ظروف ضغط وحرارة قياسية bg:Стандартни температура и налягане ca:Condicions normals de pressió i temperatura de:Standardbedingungen et:Normaaltingimused el:Κανονικές Συνθήκες Πίεσης και Θερμοκρασίαςfa:استاندارد دما و فشار fr:Atmosphère normalisée ko:표준 온도 압력 is:Staðalaðstæður it:Condizioni normali he:תנאים סטנדרטיים של טמפרטורה ולחץ lv:Normāli apstākļi (ķīmijā) hu:Normálállapot ms:Suhu dan tekanan piawai nl:Standaardomstandigheden ja:標準状態 no:Standard trykk og temperatursimple:Standard temperature and pressure sr:Нормални услови fi:NTP sv:Standardtryck och -temperatur vi:Nhiệt độ và áp suất tiêu chuẩn

WikiDoc Help Menu Quick Start.. Get Started Here! How to Login How to Search Pages How to Start a New Page How to Edit a Page Cheat Sheet Editing basics Learning Basic Formatting How to make Links in WikiDoc & to External Sites How to Make Lists How to Ignoring Formatting Adding References or Footnotes to Articles Tracking Changes You Have Made How to Put an Article Into a Category When Multiple Topics Should Go To The Same Page (MI, Acute MI, AMI) Using Redirection Advanced editing How to Make Tables How to Insert Images and Other Media How to Add Video Help:How to Make Columns Web Colors How To Make Templates How to Move Pages Inserting Dynamic Dates and Times Inserting WikiDoc Statistics Editing the Table of Contents Communicating your edits Let others know what you changed: The importance of Edit Summaries Minor Edits Edit Conflicts Help Videos You Can Watch Getting Started Video

Acknowledgement and Attribution Regarding Sources of Content

Some of the initial content on this page may be incorporated in part from copyleft sources in the public domain including wikis such as Wikipedia and AskDrWiki. Drug information for patients came from the The National Library of Medicine. Infectious disease information may have come from the Centers for Disease Control (CDC). Differential Diagnoses are drawn from clinicians as well as an amalgamation of 3 sources: 1.The Disease Database; 2. Kahan, Scott, Smith, Ellen G. In A Page: Signs and Symptoms. Malden, Massachusetts: Blackwell Publishing, 2004:3; 3. Sailer, Christian, Wasner, Susanne. Differential Diagnosis Pocket. Hermosa Beach, CA: Borm Bruckmeir Publishing LLC, 2002:7 .